Strength of Materials

About this subject

Practice questions

Showing page 1 of 6. Select an option to practise inline.

Open full list →

Show Answers

Correct options are highlighted when revealed.

1.Up to which point does Hooke's law remain valid?

The point where permanent deformation beginsThe limit of proportionalityThe point at which the material fracturesThe maximum elastic strain pointThe onset of plastic deformation

2.What is the unit of Young's modulus?

3.When a body is subjected to equal and opposite forces that attempt to stretch it, the resulting stress is known as______________________?

4.What is the modulus of rigidity defined as the ratio of?

Axial stress to axial strainPressure stress to volumetric strainTransverse stress to transverse strainShear stress to shear strainTensile stress to lateral strain

5.How does the ultimate tensile strength of mild steel compare to its ultimate compressive strength?

6.When a thin mild steel wire is subjected to gradually increasing loads in equal steps until it fractures, how does the extension change with the applied loads?

Remains constant throughoutIncreases at a steady rateRises initially and then diminishesGrows steadily at first, then accelerates rapidlyIncreases rapidly at first, then steadily

7.What happens to the Young's modulus of a wire if its radius is increased to twice its original size under the same load?

8.How is the tensile strength of a material calculated during a tensile test?

Cross-sectional area measured at the point of fractureInitial cross-sectional area before the test beginsMean value between the initial and fracture cross-sectional areasSmallest cross-sectional area observed after fractureNone of the listed options

9.What is the amount of elongation in a wire relative to its original length when the applied stress equals the Young's modulus?

10.What is the term for the stress magnitude that produces a unit strain in a material?

11.A tensile test was performed on a specimen with an initial cross-sectional area of 1 cm². The maximum load recorded was 8 tonnes, and the cross-sectional area at the necking point reduced to 0.5 cm². What is the ultimate tensile strength of the specimen?

13.During a tensile test on a mild steel sample, how does the breaking stress compare to the ultimate tensile stress?

Greater than the ultimate tensile stressLower than the ultimate tensile stressEqual to the ultimate tensile stressVaries depending on the steel's compositionCan be any value without restriction

15.What is the typical range of Poisson's ratio for steel?

16.The elongation experienced by a uniform bar hanging vertically due to its own weight is equivalent to the elongation caused by which of the following weights applied at the bar's lower end?

A weight equal to the bar's weight applied at the bottomA weight equal to half the bar's weight applied at the bottomA weight equal to half the square of the bar's weight applied at the bottomA weight equal to one-quarter of the bar's weight applied at the bottomNone of the above

How to prepare with Strength of Materials MCQs

Work through questions topic by topic, then revisit any you answered incorrectly.
Read explanations carefully—they often cover facts that repeat across PPSC, FPSC, and NTS papers.
Pair subject practice with past papers to see how Strength of Materials appears in real exam conditions.

Strength of Materials

About this subject

Practice questions

1.Up to which point does Hooke's law remain valid?

2.What is the unit of Young's modulus?

3.When a body is subjected to equal and opposite forces that attempt to stretch it, the resulting stress is known as______________________?

4.What is the modulus of rigidity defined as the ratio of?

5.How does the ultimate tensile strength of mild steel compare to its ultimate compressive strength?

6.When a thin mild steel wire is subjected to gradually increasing loads in equal steps until it fractures, how does the extension change with the applied loads?

7.What happens to the Young's modulus of a wire if its radius is increased to twice its original size under the same load?

8.How is the tensile strength of a material calculated during a tensile test?

9.What is the amount of elongation in a wire relative to its original length when the applied stress equals the Young's modulus?

10.What is the term for the stress magnitude that produces a unit strain in a material?

11.A tensile test was performed on a specimen with an initial cross-sectional area of 1 cm². The maximum load recorded was 8 tonnes, and the cross-sectional area at the necking point reduced to 0.5 cm². What is the ultimate tensile strength of the specimen?

12.Identify the quantity among the following that is dimensionless and has no units.

13.During a tensile test on a mild steel sample, how does the breaking stress compare to the ultimate tensile stress?

14.Among the materials listed below, which one exhibits the highest elasticity?

15.What is the typical range of Poisson's ratio for steel?

16.The elongation experienced by a uniform bar hanging vertically due to its own weight is equivalent to the elongation caused by which of the following weights applied at the bar's lower end?

17.What term describes materials that have identical elastic characteristics regardless of direction?

18.What is the term for a material's ability to be stretched into a thinner shape without breaking?

19.Which of the following materials has a Poisson's ratio exceeding one?

20.How does the unit volume of a material subjected to tension change as its Poisson's ratio increases?

How to prepare with Strength of Materials MCQs

More on PakQuizHub